You searched for steam case studies - Armstrong | Korea

Product

Thermostatic Bellows Steam Trap – TT Series

Armstrong Thermostatic Steam Traps are available with balanced-pressure bellows or wafer-type elements and are constructed in a variety of materials, including stainless steel, carbon steel and bronze. These traps are used on applications with very light condensate loads. THERMOSTATIC OPERATION Thermostatic steam traps operate on steam’s temperature difference from cooled...

Product

Steam Quality Monitoring – Steam QM®-3

Steam QM®-3 is an intelligent solution that allows pharmaceutical manufacturers, hospitals, and other healthcare facilities concerned with steam quality to easily and efficiently measure the quality of steam used for sterile applications. Steam QM®-3 is an automatic steam quality monitor that determines and communicates steam moisture content, the amount of...

Product

Steam-To-Steam Humidifier – CS Series

CS Series steam-to-steam humidifiers use existing boiler steam to produce clean steam from untreated water. Because these humidifiers use steam from a central boiler as a heat source, the humidifying steam can be produced more economically than from electricity. CS Series humidifiers consist of a heat exchanger submersed in a...

Product

Steam Quality Monitoring – Steam QM®-1

Until now measuring steam dryness fraction has largely been a manual process, which is time consuming and presents inherent safety and accuracy risks. Steam QM®-1 is an automatic steam quality monitor that continuously determines and communicates the dryness fraction of steam for more efficient management of a steam network. Steam...

Product

Duralite™ Plate Fin Steam Coils

Armstrong Duralite™ plate fin steam coils are available in Centifeed (steam-distributing tube-type), Standard (opposite-end connections), and Two-Row Return-Bend construction. Centifeed, Standard and Return-Bend coils are made of 0.625″ OD tubes as standard. One-Row coils with 1″ OD tubes are available as options. Depending on steam flow, long Centifeed coils may...

Product

Clean Steam Thermostatic Steam Trap – TC Series

Armstrong offers a complete range of TC Series traps to handle the special requirements of clean steam systems. Different body configurations are available for choice of piping and ease of cleaning. The TC Series traps are constructed from 316L stainless steel for corrosion resistance and are highly polished for cleanability....

Product

Steam Harness

Every pellet mill or extruder, whether new or existing, has unique piping configurations and mechanical support requirements, so Armstrong begins by doing an on-site assessment. We measure your physical space, identify restrictions, and determine the specific needs of your facilities surrounding the pellet mill or extruder before customizing your Armstrong...

Product

Thermostatic Air Vent – TTF Series

Armstrong offers thermostatic air vents for positive venting of air and other non-condensable gases from steam in chamber-type heat-transfer equipment. Typical applications include jacketed kettles, retorts, vulcanizers, jacketed sterilizers or other contained equipment where air could accumulate in remote areas of the steam chamber and reduce heat-transfer capacity. These vents...

Product

Heavy Duty Steam Heating & Liquid Coils – 6000 Series

Armstrong offers a full line of coils capable of handling virtually any service—from light-duty applications to the toughest and harshest of industrial jobs. And with our custom capabilities, we will literally build a coil to do exactly what you need it to do. No off-the-shelf solutions here. You get the...

Product

AIM® Steam Trap Monitoring – WirelessHART®

Armstrong Intelligent Monitoring – AIM® 5700 – is a wireless monitoring technology that efficiently monitors and evaluates steam trap operation. The AIM® 5700 identifies the conditions of a steam trap to determine significant problems that could put your operation at risk. The AIM® 5700 can accurately detect potential issues such...

Product

Inverted Bucket Steam Trap – 800 Series

800 Series Inverted Bucket Steam Trap in cast iron for horizontal installation, with continuous air venting at steam temperature, free-floating stainless steel mechanism, and discharge orifice at the top of the trap. The most reliable steam trap known—the inverted bucket—provides efficient condensate drainage of virtually all types of steam-using equipment....

Product

Inverted Bucket Steam Trap – EM Series

Armstrong’s type EM forged steel inverted bucket steam trap combines the most reliable steam trap operating principle known in a body, which can be opened for easy maintenance. The EM Series offers high resistance to wear, corrosion and water hammer. The free-floating guided lever valve mechanism is “frictionless” with all...

Product

Inverted Bucket Steam Trap – 880 Series

880 Series Inverted Bucket Steam Trap in cast iron for horizontal installation with integral strainer, continuous air venting at steam temperature, free-floating stainless steel mechanism, and discharge orifice at the top of the trap. The most reliable steam trap known—the inverted bucket—provides efficient condensate drainage of virtually all types of...

Product

Bimetallic Steam Trap For Superheat Conditions – SH-4000 Series

SH-4000 Series Bimetallic Steam Traps are the ideal design for applications involving superheated steam. During start-up, the bimetallic mechanism is fully open and allows large volumes of non-condensable gases and condensate to be removed from the system. As the system reaches saturated steam conditions, the mechanism begins to close preventing...

Product

Inverted Bucket Steam Trap – Models 401-SH & 501-SH

Models 401-SH and 501-SH in carbon steel or stainless steel for vertical installation are made for overcoming the difficult combination of superheat and high pressure/low load service. To survive this most severe steam service, Armstrong created an inverted bucket trap with a unique accumulation chamber. The chamber collects sufficient condensate to...

Product

Inverted Bucket Steam Trap – 200 Series

200 Series Inverted Bucket Steam Trap in cast iron for vertical installation, with continuous air venting at steam temperature, free floating stainless steel mechanism, and discharge orifice at the top of the trap. The most reliable steam trap known-the inverted bucket-provides efficient condensate drainage of virtually all types of steam-using...

Product

Float & Thermostatic Steam Trap – B & BI Series

Armstrong B and BI Series Float & Thermostatic steam traps combine high standards of performance and long life with economy. They are ideal for heating service where continuous drainage with high air-venting capacity is required. Due to the wide use of vacuum returns in systems of this type, the thermostatic...

Product

AIM® Steam Trap Monitoring – ISA100

Armstrong Intelligent Monitoring – AIM® 6700 Series – is a wireless monitoring technology that efficiently monitors and evaluates steam trap operation. The AIM® 6700 Series identifies the conditions of a steam trap to determine significant problems that could put your operation at risk. The AIM® 6700 Series can accurately detect...

Product

Inverted Bucket Steam Trap – 600F and 680F Series

600F Series Inverted Bucket Traps, ductile iron construction with integral flange, continuous venting at steam temperature, free floating stainless steel mechanism, drain hole on top of the trap. The most reliable steam trap known—the inverted bucket—provides efficient condensate drainage of virtually all types of steam-using equipment. Put the inverted bucket...

Product

Controlled Disc Steam Trap – CD-72SR

The Armstrong CD-72SR is a disc-style steam trap designed to control the trap’s cycle rate. By reducing the cycle rate, the CD-72SR will have a longer service life than typical disc traps. This enhanced performance will ensure that maintenance time is minimized and steam costs are greatly reduced. The CD-72SR...

Product

Steam Distribution Manifolds – MSD & SMSD

Armstrong MSD and SMSD Steam Distribution Manifolds place all steam supply valves in one location. Standardizing components and centralizing their location simplifies installation, reduces costs, and makes routine maintenance easier. Benefits of Armstrong Steam Distribution Manifolds Reduced design specification costs Dimensional consistency Space savings Lower installation costs, due to prefabrication...

Product

Bimetallic Steam Trap For Superheat Conditions – SH-900 Series

SH-900 Series Superheat Steam Traps operate by the effect that rising temperature has on the thermostatic bimetallic elements. At start-up, the valve is wide open, which allows a large volume of non-condensables and cold condensate to be removed from the system. When the system reaches steam temperature, the elements become...

Product

Inverted Bucket Steam Trap – 980 Series

The most reliable steam trap known-the inverted bucket-provides efficient condensate drainage of virtually all types of steam-using equipment. Put the inverted bucket to work in a tough cast iron package, and you have the best of both worlds. Because they operate efficiently for longer periods of time, Armstrong cast iron...

Product

Float & Thermostatic Steam Trap – JD & KD Series

The simple, yet rugged, ductile iron construction of the JD & KD Series Ultra-Capacity Float & Thermostatic steam traps offer long, trouble-free service. All floats, valves and seats and lever mechanisms are constructed of stainless steel. The integral thermostatic air vent is a balanced-pressure phosphor-bronze bellows caged in stainless steel....